Xprite 4" Inch LED Fog Lights | White Led Chip Fog Lamp Compatible with 2007-2018 Jeep Wrangler Unlimited JK Driving Off Road Fog Light

Good quality

Well suited to my Jeep JK with accurate cable connections. Good amber lighting. Suited for Road lights as well.

The factory lights on my 2016 Cherokee Trailhawk are incredibly inadequate. These fog lights are a step in the right direction and are what the Jeep should have had as OEM equipment. Expect to spend about an hour installing these. Though it *can* be done without removing the front wheels, just make your life easier and take off the wheel. I spent about 45 minutes on the driver's side and didn't take off the wheel, and the passenger was much less than 30 minutes including taking off the wheel. And use a wobble-socket. The only tools needed are an 8mm socket for the fender liner and 7mm for the lights. a piece of wire or a bungee cord will hold the fender liner out of your way. Fit-up was a perfect match with the factory mount and wiring, and I get no error codes (though I don't think the fogs throw a bulb error anyway). I can finally see in the dark.Next step...new headlights!

Compared to the stock fog lights, there's no comparison obviously. The construction is solid and higher quality than some I've seen, and they're not just brighter, they also have a wider view pattern, so I'm able to see a wider area of the road before.Installation was a snap...literally plug-n-play and they were easy to adjust. I'm definitely an Xprite customer going forward!UPDATE - I paired them with a set of Opar LED headlights, and together they fill the road with light without blinding oncoming traffic.UPDATE - Sept 5/2018 - Noticed some fogging and water leakage in one of the lights. All it means is the seal has finally let go and the affected light needs to be dried out and re-sealed. I've used these NON-STOP for almost 2 years driving regularly...and I would only replace these with these again. They're very much worth getting.

Very nice looking they feel very heavy and well-built. Yes you can install them without removing the bumper. Take the splash guard off loosen the four swaybar bolts not hard to do you can reach up and use Phillips screwdriver 4 screws aside. Use dielectric grease in the connecters and put some in the back where the wires go in to the fog light for extra protection. If the connecter does not want to plug together such as one of mine did just take a small screwdriver and you can position the pins on the fog light connecter then connect themPress hard until they click. They look great I can’t tell you how long they will last but so far I like them I got the amber color.

They look amazing! They are plug--play for the Fog light function. Comes with an adaptor harness that plugs right in. The extra wire is for the halo. The ground is shared from the main plug. . I wired the halo to the same circuit as the halos for the headlights. So they come on with the ignition switch and are always on.9-May-2108 Update:1 light has stopped working. The halo is still working but the main light is dead.Trying to see if it might be a harness issue, but have not determined 100% yet.They have a 1 yr warranty only.Once I am certain of the failure mode , I will post an update.7-Jul-2022 UpdateInstalled this set last summer and I have lost the halo on the passenger side already.Not certain why, but that side always seems to get water in it. I even sprayed this set with clear coat on the back to try and seal them more.The lights both still work as fog/driving lights, but only one halo works.

Exceptionally bright and really crisp color. Easy installation with clear instructions. The wiring is of good quality and it is plug and play for a jeep jk. There is a good length of wire so it should fit Jeeps with aftermarket bumpers too. It matches perfectly with my jw speaker 8700j headlights in terms of headlight design, light color, and light output. The housing are an exact match for the factory jk fog lights and fit perfect. However, after 7 months of use I have experienced water ingress as pictured. The lights still function but the lens is cloudy and there’s a bit of water pooled in the bottom.